A 5.5 or 6.5 HP petrol engine runs much faster than an HTP pump should turn, so the belt and pulleys between them have to bring the speed down. Our JPK-QF-168 engines run at 3000 to 3600 rpm and the HTP pump on our sprayer sets turns at 800 to 1200 rpm, which means the pump pulley has to be roughly 2.5 to 4.5 times the diameter of the engine pulley.
Why can the engine not drive the pump directly?
Because the two are built for different speeds. A plunger pump run over its rated speed wears its plungers fast, and one run under speed never reaches its rated pressure. The engine only has to hold the speed. Flow and pressure come from the pump.
| Engine | Power | Speed | Max. torque | Weight |
|---|---|---|---|---|
| JPK-QF-168-5.5 | 5.5 HP | 3000 to 3600 rpm | 13 N.m | 14.3 kg |
| JPK-QF-168-6.5 | 6.5 HP | 3000 to 3600 rpm | 13 N.m | 14.3 kg |
Both are four stroke engines on plain petrol, sold loose on our gasoline engine 6.5 HP and 5.5 HP page for buyers who fit their own pump.
Which JP Kissan pumps can a 5.5 or 6.5 HP engine drive?
Start from the pump's power rating, never from the engine. An engine that is only just big enough drops below its rated rpm the moment load comes on, and the pump then loses pressure and delivery together.
| Pump | Pump speed | Suction | Power needed | On a 5.5 or 6.5 HP engine |
|---|---|---|---|---|
| JPK-30-1 | 800 to 1200 rpm | 30 to 50 L/min | 2 to 3 HP | Comfortable on either |
| JPK-50-1 | 800 to 1200 rpm | 40 to 60 L/min | 3 to 5 HP | Covered by either |
| JPK-90-1 | 600 to 1000 rpm | 50 to 90 L/min | 5.5 to 9.5 HP | Bottom of its range only |
| Ashoka 888 (85) | 1200 rpm spraying | 85 L/min spraying | 8.0 HP spraying | Too small for spray duty |
The JPK-150 and JPK-180 need 7 to 9.5 HP, so neither engine suits them. The full range is on our HTP pump page.
How do you work out the pulley ratio?
- Note the engine speed you will run at, between 3000 and 3600 rpm.
- Note the pump's rated speed from its model page.
- Divide the engine speed by the pump speed. That is the ratio.
- The pump pulley diameter must be the engine pulley diameter multiplied by that ratio.
| Engine speed | Pump at 800 rpm | Pump at 1000 rpm | Pump at 1200 rpm |
|---|---|---|---|
| 3000 rpm | 3.75 : 1 | 3 : 1 | 2.5 : 1 |
| 3600 rpm | 4.5 : 1 | 3.6 : 1 | 3 : 1 |
What does a worked example look like?
Say you want a JPK-50-1 at the top of its range, 1200 rpm, on a JPK-QF-168-6.5 held at 3600 rpm. The ratio is 3600 divided by 1200, which is 3 : 1. As an example, if the engine pulley measures 75 mm across, the pump pulley needs to be about 225 mm. The same engine on a JPK-90-1 at 1000 rpm needs 3.6 : 1, a larger pump pulley again, because that pump is built to turn slower.
What else has to match before the set will run?
- The shaft: diameter, length, key, keyway and the bolt pattern on the mounting face must suit your pulley. A shaft that will not take your pulley is the most common reason a replacement engine goes back.
- The pressure gauge: every JP Kissan pump carries one. If the set cannot reach the pump's rated pressure with the engine at speed, check the ratio and the engine size before blaming the pump.
If you would rather not build the drive yourself, our complete power sprayer sets come with the pump, drive and pulley ratio matched and run at our works before dispatch.
How do you get a quote for an engine and pump?
Send us the pump model you have or want, the engine power, a photograph of the old shaft or mounting face, the quantity and your city. We will confirm the fit and the pulley ratio before quoting.